Plumbing services in Cardiff
Dripping taps, slow-flushing toilets, leaks, new pipework and everything in between. Marvel Plumbing Services gives you a straight answer on what needs doing and what it will cost, then fits it properly and tidies up.
Signs it's time to call a plumber
Most plumbing faults give you a warning first. Catching them early usually means a smaller job and a smaller bill. Ring us if you spot any of these:
- A tap that drips even when it's turned off hard, which usually means a worn washer or cartridge
- Damp patches, stained ceilings or a musty smell near pipes, a bath or a toilet
- Water pressure that has dropped on one tap or across the whole house
- A toilet that keeps running, refills on its own or is slow to flush
- Hot water that's patchy, slow to arrive or runs cold quickly
- Banging or knocking pipes when taps are turned on or off
- A stopcock that won't turn, so you can't isolate the water in an emergency
What we can do for you
Small jobs and big ones get the same care. The common ones:
- Repairing or replacing taps, washers, cartridges and flexible hoses
- Toilet repairs, cistern valves, flush mechanisms and replacement toilets
- Finding and fixing leaks on supply pipes, waste pipes and under sinks and baths
- New and replacement pipework for kitchens, bathrooms and utility rooms
- Fitting outside taps, washing machine and dishwasher connections
- Stopcocks, isolation valves and general repairs to hot and cold water systems
Need a whole room doing? That's covered under bathroom re-fits and upgrades, and we also do radiator installation.
Pipes, fittings and what we'd choose
The right material depends on where the pipe runs, what it's joining to and how much of the old system is staying. We'll explain the options before we start.
Copper
The long-standing choice for visible runs and hot water. Strong, neat and joined with soldered or compression fittings.
Plastic pipe
Flexible and quick to fit in tight spaces such as under floors. Suits hidden runs where copper would mean lifting a lot.
Push-fit connectors
Good for repairs and awkward spots where a flame isn't sensible. Fitted correctly, they're reliable and tidy.
Compression joints
Used for taps, valves and connections that may need to be undone again later without heat.
How a plumbing job is done properly
- We look at the problem firstWe find the cause, not just the symptom, so you're not paying twice for the same leak.
- You get a clear quoteFree, with what's included spelled out before any work begins.
- We protect your homeDust sheets down, water isolated and the work area kept contained.
- The work is fitted and pressure-testedEvery joint is checked under pressure, with taps and valves run through before we pack up.
- We clean up and talk you through itThe area is left clean, and we show you where the stopcock is and what we've changed.
Standards the work has to meet
Domestic plumbing in the UK is covered by the Water Supply (Water Fittings) Regulations 1999. They exist to stop contamination and waste, so fittings must be approved and installed to a set standard. Building Regulations also apply to new bathrooms, drainage and hot water safety, and we work to them.
Our plumbers hold City & Guilds Level 2 and Level 3 Plumbing and an NVQ Level 2. One thing to know: gas appliances, such as boilers and gas fires, must only be worked on by a Gas Safe registered engineer. If a job involves gas, we'll say so plainly.
What affects the cost
Every house is different, so we quote after seeing the job. These are the usual factors:
- How easy the pipes are to reach, for example under floorboards or behind tiles
- The condition of the existing pipework and fittings
- The parts needed, from a washer to a full set of new taps or valves
- Whether it's one repair or several jobs that can be done in the same visit
- Whether the job needs finishing work, like making good after a leak
Quotes are free and you'll know the price before we start.
Looking after it afterwards
A little upkeep keeps new work trouble-free.
- Know where your stopcock is and turn it every few months so it doesn't seize
- Lag exposed pipes in lofts, garages and outbuildings before winter
- Don't flush wipes, and keep fat and grease out of sink waste
- If a drip or damp patch returns, ring us rather than leaving it, because small leaks get bigger
Plumbing questions we get asked a lot
How do I stop the water if a pipe bursts?
Turn the stopcock clockwise to shut off the mains. It's usually under the kitchen sink or near the front door. Then open the cold taps to drain the pipes and switch off the electrics if water is near sockets. Ring Marvel Plumbing Services once it's off and we'll tell you what to do next.
Do you carry out gas work?
Gas appliances such as boilers and gas fires must be worked on by a Gas Safe registered engineer, so always check their card. Marvel Plumbing Services covers water pipework, taps, toilets, radiators and bathrooms. If your problem involves gas, we'll tell you straight.
Is the quote really free?
Yes. We look at the job, explain what's needed and give you a clear price before any work starts. There's no charge for the quote and no pressure to accept it.
Will you do a small job like a dripping tap?
Yes. Washers, tap cartridges, cistern valves and similar repairs are everyday jobs for us. Small faults are worth fixing early, before they cause damp or waste water.
Do I need to be at home while you work?
Usually it's easiest if someone is there at the start to show us the problem and at the end to go through the finished work. If that's not possible, ring us and we'll talk through what suits.
Which areas do you cover?
Marvel Plumbing Services is based in Cardiff and covers most of South Wales, including Newport and Swansea. Ring or send a quote request and we'll confirm we can get to you.
Got a leak or a job that needs doing?
Tell us what's going on and we'll give you a free quote. If it can't wait, ring.